Progress Photos 2019 - Part 1

As promised, photos. This time with minimum words...…. Apologies if any photos are repeats.
First up, my fuses residing in the glove box. They swivel out for access (on a chopped up nylon cutting board) and rotate back in to hide away nicely.

And now the instrument cluster as you view it from the driver seat. It nicely fits inside the radius of the steering wheel. No swinging your head left to right to "look around your hands" to see the outer gauges like you need to do on the standard early Mustang gauge cluster.

This next photo shows a custom crank scraper i built to peel oil off the rods/crank. It seems to work nicely and gives about a 3mm gap to all rotating parts. The extra angled strip you can see that I've added directs windage/oil down the side of the sump and simply "away" from the crank. The sump uses windage in the shallow middle section to drive oil to the rear via those angled baffles, while perforated/vented plates (not shown) that cover each end of the sump keep oil down near the pickups. The pickups themselves are slots cut into the bottom of pickup tubes at each end of the sump. You can the curved front pickup tube below. The natural angle of the engine in the engine bay means oil accumulates at the rear of the "humps" in the sump - so this is where the two pickups are, You can also see some plates that i've added (that sit about an inch above the pickup tubes that (in theory) stop oil rising back up to the crank on acceleration. This combo works a treat now, no oil starvation evident at all, no matter how the car is flung around.

To reduce noise I used these standard silencer cones but modified them to make sure they stayed centred in the 3" pipes.

Ah! Now some relatively recent photos of the car coming together. It's looking ok.

Now the photos below show an annoying problem i found that was tricky to diagnose and fix. The front of the motor had an oil leak.....

If you look closely at the photo below, you may notice that the upper part (the upper lip) on the camshaft seal (which with the motor in this photo sitting upside-down, is in fact the bottom of the bottom hole), is damaged.

Why? Because the whole front cover was mounting itself about 3mm too low on the front of the block. This "crimped up" the cam and crank seals along their top edge, plus causing a gap for each at their bottom edge. Oil just..... well.... leaked out and got flung about by the spinning crank & external cam drive. It was only a dribble leak, but very annoying. The fix was simple enough. Elongate each bolt mounting hole in the timing cover downwards by 3mm, clean everything up, then use new cam-drive and harmonic balancer seals to "center" the front timing cover before tightening up the bolts to bolt it back in place in the correct position. Not a drop of oil leaks now - much better. 

Oh - and I have built a cold air intake now to draw air in thru the '67 hood scoops. See an "in progress" photo below. That little inner frame now contains the foam air filters. The outer edges of the box you see below and top of the filter frame (not yet built in this photo) seal against the underside of the hood so air can only enter via the hood scoops, then flow around the front and sides of the inner "filter frame", then pass through the filters to enter the central area where the 8 trumpets sit.

Below was a brake fix (an upgrade) I made by swapping out the old 6" diameter single diaphragm booster for an 8" twin diaphragm unit. The mechanical roller cam just didn't have enough vacuum for the 6" diaphragm in stop/start traffic for my liking. I also changed the pedal to pushrod ratio to better balance the entire setup. Brakes work much better now.

And now for the 4-Link setup.....

Only after the chassis got its "gold star pass" on the chassis torsion test did my vehicle engineer say... "just make it a 4-Link". So I did and here are the photos of the results.

In the photos above and below, the RRS rear torque arm is still attached to the nose of the diff. This was removed before final installation to clean things up and give a bunch of room back in the driveshaft tunnel.
Oh - and the teeny weeny rear disks you see here will be replaced with much bigger units...… These just came with the floating hub kit. I didn't realise they would be so small at the time.

Once the chassis and diff "link mounts" were tacked in and mocked up to ensure I had lots of adjustment options, I bolstered the frame-rail mounting points to spread load over a much larger area of the chassis. The photos speak for themselves I hope. All steel plate and 35mm right-angle was 3mm thick.

I can't tell you the difference the 4-link has made over the 3 link as I simply didn't get to drive it enough to be able to compare. All I know is the new 4-Link works just fine and the car seems to hook up ok. Well - depending on your right foot that is, as the engine simply overwhelmes street tyres if you give it some stick (as you can imagine).

Also, here is how I made the lower control arms on the front suspension adjustable...… See below.
Years ago I cut off the inner ends of the original control arms and welded in two lock nuts to give me thread for screwing in a heim-joint. But I always worried in the back of my mind that I never had enough thread. So rather than hack into these, I bought two new after-market control lower arms and modified them. As you can see I used some spare chrome-moly tube I had left over from the 4 links, and welded these in. So now - no matter how far you screw in the heim joints - they only engage more and more thread. Much more comforting.

Boxing these arms makes them much much stronger too.

Now for the front valence...…
As you can see, I have welded the stone-tray and valence together into a single unit and this includes a cols air scoop for the lower half of the radiator and engine oil cooler. But as you can see, the fit to the front fenders was initially awful. The photos below this miss-alignment and then resultant fix for each side. First the Australian passenger side.

And now the drivers side. Had to fix some big gaps here!

As I write this I am just mounting the front bumper with its custom mounts after cutting/shutting the bumper to tuck it in, in a much more flush manner.
More photos to come as well, seeing I am about to get the car thru engineering tests and rego'.
Stay tuned.